Science and technology of Kazakhstan
search Find
THERMODYNAMIC MODELING OF PHASE TRANSFORMATIONS IN 40CRNI3MOV STEEL WITH DIFFERENT MODIFICATIONS
Annotation
Thermodynamic modeling of phase transformations in the structural alloy steel 40KhN3MF under various chemical composition modifications was performed using the Thermo-Calc software package (version 2025, TCFE13 database). Polythermal sections were constructed and analyzed for the base composition, steel with 1.5% Mo addition, and steel with a complex modification involving the addition of 0.4% each of Cr, Ni, Si, and Al. It was established that the addition of molybdenum increases the thermal stability of carbide phases (particularly M₂₃C₆ and MC), which inhibits carbide coalescence upon heating, thereby promoting dispersion strengthening and enhanced wear resistance. The complex modifiers, in turn, contribute to the stabilization of the austenite phase (notably due to Ni and Al), reduction in the formation of coarse carbides and intermetallic compounds, and an increase in the alloy's plasticity owing to structural homogenization. The conducted analysis of phase transformations enabled the precise determination of the temperature ranges for complete austenitization and dissolution of the primary carbide phases. This provides a basis for optimizing heat treatment regimes (including quenching and tempering temperatures) to achieve a fine-grained, strong, and homogeneous structure. The simulation results can be utilized in designing steel compositions and heat treatment technologies to improve their service properties in critical components
Author
A. A. Tuganbaeva
S. K. Arinova
Sv. S. Kvon
A. Z. Isagulov
DOI
https://doi.org/10.48081/SBFK4865
Keywords
steel
polythermal cuts
modifiers
crystallization
phase
Year
2025
Номер
Issue 3
For citation:
A. A. Tuganbaeva, S. K. Arinova, Sv. S. Kvon, A. Z. Isagulov THERMODYNAMIC MODELING OF PHASE TRANSFORMATIONS IN 40CRNI3MOV STEEL WITH DIFFERENT MODIFICATIONS // Scientific journal "Science and Technology of Kazakhstan". - 2025 - №3 - С. 334– 344. https://doi.org/10.48081/SBFK4865
Copied!
IMPROVING THE TECHNOLOGY OF ROLLING GRINDING BALLS WITH A DIAMETER OF 125 MM
Annotation
The results of computer simulations and experimental studies aimed at improving the technological process for manufacturing grinding balls with a diameter of 125 millimeters and enhanced operational properties for use in the mining industry in Kazakhstan and the metallurgical sector are presented. The demand for grinding balls of different grades and hardness is constantly growing. At the moment, balls with a diameter of 125 millimeters are imported from China. Therefore, the current trend is to increase the range of grinding media manufactured in the Republic of Kazakhstan. One of the key aspects in determining the optimal technological process for producing balls is the calculation of the sizing of the equipment used in a ball rolling mill. This paper presents a calculation of the sizing for rolling rolls used to produce a ball with a diameter of 125 millimeters, while the rolls have a diameter of between 440 and 460 millimeters. Based on the results of computer simulations, the relationship between the intensity of deformations and the radius of the bridge while the ball is rolling has been determined. A comparative analysis of the mechanical properties, specifically the hardness of the resulting balls in cross-section, revealed that the main subsurface layers, with a thickness of approximately 20 millimeters, have a significantly increased hardness ranging from 55 to 58 HRC. Based on the findings of the study, there were no hardness failures directly in the center of the ball, indicating the absence of internal flaws and the good quality of the metal in the inner layers.
Author
A.V. Bogomolov
A.K. Zhunussov
Zh.B. Kazhmukhambetov
S.S. Spanov
A.K. Zhunusova
DOI
https://doi.org/10.48081/APSR7381
Keywords
ball
rolled products
steel
calibration
strain intensity
hardness
Year
2025
Номер
Issue 3
For citation:
A.V. Bogomolov, A.K. Zhunussov, Zh.B. Kazhmukhambetov, S.S. Spanov, A.K. Zhunusova IMPROVING THE TECHNOLOGY OF ROLLING GRINDING BALLS WITH A DIAMETER OF 125 MM // Scientific journal "Science and Technology of Kazakhstan". - 2025 - №3 - С. 226 –235. https://doi.org/10.48081/APSR7381
Copied!
ON THE PROBLEM OF DESIGNING A VEHICLE WITH HYBRID PROPULSION
Annotation
The article considers current issues of designing vehicles with hybrid propulsion in the context of modern environmental, economic and technological challenges. Particular attention is paid to hybrid vehicles that combine the advantages of internal combustion engines and electric motors, which helps to reduce emissions, save fuel and increase operational efficiency. The work emphasizes the importance of hybrid vehicles as a compromise option in the context of tightening environmental standards and rising energy prices. A review of the layout schemes of hybrid propulsions: parallel, series and combined series and parallel is given with an analysis of their design features, advantages and disadvantages. Particular attention is paid to increasing efficiency, reducing fuel consumption and compliance with environmental standards. The work is based on literary sources and demonstrates the importance of hybrid technologies as a promising direction in transport engineering. The article is devoted to the design and research of a vehicle with hybrid propulsion, carried out at the Department of Transport Equipment and Logistics of the Toraighyrov University. The design of a vehicle with hybrid propulsion helps expand the functionality of the vehicle, ensuring its adaptability, energy efficiency and environmental friendliness. Such solutions allow the integration of intelligent control systems, which increases the reliability and stability of vehicles in various operating conditions.
Author
А.А. Rakisheva
S.B. Kokin
V.S. Yessaulkov
Petr Bouchner
K.K. Abishev
DOI
https://doi.org/10.48081/GXFT8138
Keywords
vehicle
automotive design
battery
combined propulsion
hybrid propulsion
Year
2025
Номер
Issue 3
For citation:
А.А. Rakisheva, S.B. Kokin, V.S. Yessaulkov, Petr Bouchner, K.K. Abishev ON THE PROBLEM OF DESIGNING A VEHICLE WITH HYBRID PROPULSION // Scientific journal "Science and Technology of Kazakhstan". - 2025 - №3 - Р. 359 – 367. https://doi.org/10.48081/GXFT8138
Copied!
THE ROUND SHAPED CUTTERS PROFILE CALCULATION FOR EXTERNAL PROCESSING
Annotation
In this article, an original method for the graph-analytical profiling of round-shaped form tools for external processing is proposed, distinguished by its ability to systematize and automate calculations. Unlike existing approaches, the new method allows for the calculation of the cutter profile with a frontal surface of circular shapes, using both graphical constructions and analytical formulas. The method is based on constructing three projections of the tool profile and calculating main and auxiliary geometric parameters such as angles ε and β, as well as linear parameters Aᵢ, Bᵢ, Cᵢ and radius Rᵢ. The graphical part of the method is presented as a 12-step procedure, which includes constructing the baseline, locating nodal points, and forming the form-cutting edge profile. The analytical part of the calculation includes seven steps detailing formulas for determining design distances, inclination angles, and tool radius. The proposed method ensures high accuracy and can be implemented manually or with software, especially when individual tool geometry is required. The methodology has been tested within the framework of a project on tooling support for the manufacturing sectors of the Republic of Kazakhstan and can be applied in the design and production of high-precision form tools.
Author
B.K. Kairolla
B.N. Absadykov
A.Zh. Kassenov
A.V. Mazdubay
Kh. Mahkamov
DOI
https://doi.org/10.48081/KSOW3486
Keywords
form tool
graph-analytical calculation
external processing
tool geometry
profile radius
sharpening angles
Year
2025
Номер
Issue 3
For citation:
B.K. Kairolla, B.N. Absadykov, A.Zh. Kassenov, A.V. Mazdubay, Kh. Mahkamov THE ROUND SHAPED CUTTERS PROFILE CALCULATION FOR EXTERNAL PROCESSING // Scientific journal "Science and Technology of Kazakhstan". - 2025 - №3 - Р. 77 – 91. https://doi.org/10.48081/KSOW3486
Copied!
INCREASING THREAD CUTTING PRODUCTIVITY WITH A COMBINED TOOL
Annotation
The article discusses increasing the productivity of thread cutting on a CNC lathe using a combined tool – a comb-type cutter. The tool consists of several consecutively arranged cutting teeth that provide sequential boring and thread cutting, combining roughing and finishing operations in a single pass. Experimental studies were carried out on St20 steel blanks with a diameter of 30 mm. The cutting speed ranged from 40 to 70 m/min, the feed from 0.12 to 0.18 mm/rpm. At the same time, the thread processing time was reduced from 60 seconds (traditional chisel) to 32 seconds (comb cutter). The wear of the cutting edges under optimal conditions was 0.18 mm, which is 28% less than with a classic tool. The quality of the thread profile corresponds to GOST 24705-81 with a surface roughness of no more than Ra 1.6 microns. The comb cutter reduces vibrations and ensures uniform load distribution between the teeth, which increases tool life and processing stability. The recommended optimal modes are a speed of 60 m/min, a feed of 0.15 mm/rpm. This technology makes it possible to increase threading productivity by 40-47%, reduce cost and increase tool life, which makes it promising for mass production.
Author
B. Kozhageldiyev
A. Zh. Taskarina
Zh. K.Mussina
A. Zhankeldi
N. A. Bazhaev
DOI
https://doi.org/10.48081/LMGF9953
Keywords
comb cutter
threading
combined tool
productivity
cutting modes
tool wear
thread quality
metalworking
Year
2025
Номер
Issue 3
For citation:
B. Kozhageldiyev, A. Zh. Taskarina, Zh. K.Mussina, A. Zhankeldi, N. A. Bazhaev INCREASING THREAD CUTTING PRODUCTIVITY WITH A COMBINED TOOL // Scientific journal "Science and Technology of Kazakhstan". - 2025 - №3 - Р. 92 – 100. https://doi.org/10.48081/LMGF9953
Copied!
DEVELOPMENT DESIGN MIXER OF FEED ADDITIVE INGREDIENTS FROM PRODUCTION WASTE
Annotation
The article is devoted to the study of the influence of the degree of mixing of ingredients of a bulk feed mixture for their subsequent formation and transformation into feed additives based on waste from agro-industrial production in a new combined mixer, on their homogeneity, mixing quality, on the uniformity of distribution in the volume of the mixture of microcomponents, vitamins, on the suitability of the mixture for formation and pressing. The article presents fragments of the study of the influence of the degree of mixing of the components of the mixture on the change in the quality of feed additives and lick briquettes during their storage under various conditions. The kinetics of the process of mixing the components of feed additives and lick premixes is studied. A mechanical and mathematical model of mixing the ingredients in a mixer with a combined (composite) shaft is developed. Based on the results of experimental studies, the dependences of the form, content and hardness of the obtained feed additives and lick premixes on the composition and homogeneity of the original mixture are given. The possibility of maintaining the resistance of feed additives and lick premixes to adverse conditions, humidity and temperature of the surrounding space is analyzed. A method for selecting a rational rotation frequency of the rotor of a combined mixer has been developed and its influence on the homogeneity of the initial mixture has been determined. The results of experimental studies of a prototype of a combined mixer are presented, confirming the theoretical results obtained and proving the effectiveness and feasibility of complete and intensive mixing of the components of the mixture for the preparation of feed additives and premix licks to reduce the material consumption of the equipment and overall energy costs.
Author
A.V. Vavilov
G.A. Guryanov
B.A. Moldakhanov
E.A. Asangaliev
V.S. Yakovlev
DOI
https://doi.org/10.48081/WRCO1955
Keywords
мixer
mixing of materials
homogeneity of the mixture
feed additives
table salt
premixes
probiotics
pressing
Year
2025
Номер
Issue 3
For citation:
A.V. Vavilov, G.A. Guryanov, B.A. Moldakhanov, E.A. Asangaliev, V.S. Yakovlev DEVELOPMENT DESIGN MIXER OF FEED ADDITIVE INGREDIENTS FROM PRODUCTION WASTE // Scientific journal "Science and Technology of Kazakhstan". - 2025 - №3 - С. 33 – 49. https://doi.org/10.48081/WRCO1955
Copied!
STUDY OF THE EFFECT OF MOLYBDENUM ON THE PROPERTIES OF THE Co-Cr-Fe-Ni-Mn-Nb QHEA
Annotation
This study investigates the effects of varying molybdenum concentrations (5%, 10%, and 15%) on the microstructural features, hardness, and melt fluidity of quasi-high-entropy alloys (QHEAs) within the Co-Cr-Fe-Ni-Mn-Nb system. The primary objective is to reduce production costs of advanced alloys by partially replacing pure elemental constituents with ferroalloys. Experimental ingots were synthesized via induction melting, followed by characterization through scanning electron microscopy (SEM), Brinell hardness testing, and spiral fluidity assessments. Results indicate that increasing Mo content markedly enhances hardness – approaching a threefold increase at 15% Mo – attributable to solid-solution strengthening and probable intermetallic phase formation. However, elevated molybdenum levels negatively affect melt fluidity, with a reduction of approximately 12% observed at Mo contents between 10% and 15%, leading to casting defects. These findings emphasize the importance of optimizing molybdenum concentration to achieve an optimal balance between mechanical performance and castability. For components with complex geometries, maintaining Mo content below 10% is advisable. This work contributes to the development of cost-effective QHEAs suitable for precision casting using locally sourced materials.
Author
А.R. Abildina
DOI
https://doi.org/10.48081/VBZO5882
Keywords
quasi-high-entropy alloy
melt fluidity
molybdenum
hardness
microstructure
casting
ferroalloy
Year
2025
Номер
Issue 3
For citation:
А.R. Abildina STUDY OF THE EFFECT OF MOLYBDENUM ON THE PROPERTIES OF THE Co-Cr-Fe-Ni-Mn-Nb QHEA // Scientific journal "Science and Technology of Kazakhstan". - 2025 - №3 - Р. 207 – 214. https://doi.org/10.48081/VBZO5882
Copied!
ON COMPENSATION OF THE INCLINED POSITION OF A RAILWAY PASSENGER CAR WHEN PASSING CURVES WITH HIGH SPEED
Annotation
In this paper, the issues of maintaining a high speed of train movement on curved sections of the railway track are considered. Increasing the driving speed simultaneously increases the forces acting lateral with respect to the direction of travel, which act unpleasantly on passengers during the passage of curves. A car passing with excessive centrifugal force along a curve, in the presence of an elevation on the track, tends to lean outward with respect to the arc. turn. As a result of the wrong direction of the angle of inclination, comfort is reduced. It is proposed to give the car of a rail vehicle for the implementation of increased arc speeds an inclined position directed inside the arc. In this paper, it is proposed to combine the advantages of an active tilting system along which the rail vehicle car was rolled relative to the horizontal rodoline base by the corresponding angle of inward rotation with the help of control and actuating elements, and the advantages of a passive roll system, along which the rail vehicle car was suspended with the possibility of swinging. like a pendulum, and the longitudinal axis of the inward roll motion is always above the center of gravity of the vehicle.
Author
Ustemirova Raigul
DOI
https://doi.org/10.48081/INOW3160
Keywords
high-speed movement
carriage tilt systems
body tilt control
tilt angle
carriage rotation mechanism
Year
2025
Номер
Issue 2
For citation:
Ustemirova Raigul ON COMPENSATION OF THE INCLINED POSITION OF A RAILWAY PASSENGER CAR WHEN PASSING CURVES WITH HIGH SPEED // Scientific journal "Science and Technology of Kazakhstan". - 2025 - №2 - 458 – 471 Б. https://doi.org/10.48081/INOW3160
Copied!
ANALYSIS OF DYNAMOMETRIC MAPS OF VARIOUS STATES OF OPERATION OF THE ROD BOREHOLE PUMPING UNIT
Annotation
The article examines the analysis of various operating conditions of a downhole pumping unit using dynamometric maps. Dynamometric maps allow you to monitor the operation of the rod pump in detail: it is possible to identify defects such as gas exposure, liquid shocks, valve leakproofness, the effect of bending the polished stem and rupture of the stem. Liquid shocks are caused by a mismatch between the displacement rate of the pump and the performance of removing liquid from the tank, which leads to excessive pumping. As a result, the pump may suffer mechanical damage due to increased deflection and wear. One of the most common defects is the lack of tightness of the discharge valve or plunger. To understand the shape of the dynamometer card when the intake valve leaks, it must be borne in mind that the dynamometer card of the well shows the load depending on the displacement above the plunger. Therefore, a leak in the intake valve indicates its effect on the plunger load. Excessive accumulation of gas inside the pump can lead to a situation where the gas is completely clogged, when the gas stops working and the intake and discharge valves remain closed. Low and high displacement of the plunger also affects this condition, as leaks disrupt the efficient operation of the valves and adversely affect pump performance. A polished rod that has a malfunction is usually characterized by its bending. This bending causes significant friction between the stem and the stuffing box of the wellhead. Such friction can lead to oil leakage from the mouth or even breakage of the polished stem itself.
Author
M.M. Сhazhabayeva
A.Z. Bukayeva
A.S. Madiyarova
G.S. Mambetaliyeva
K.S. Rzayeva
DOI
https://doi.org/10.48081/CSXI4465
Keywords
pump
dynamometer
plunger
discharge valve
intake valve
liquid
pump card shape
polished rod
Year
2025
Номер
Issue 2
For citation:
M.M. Сhazhabayeva, A.Z. Bukayeva, A.S. Madiyarova, G.S. Mambetaliyeva, K.S. Rzayeva ANALYSIS OF DYNAMOMETRIC MAPS OF VARIOUS STATES OF OPERATION OF THE ROD BOREHOLE PUMPING UNIT // Scientific journal "Science and Technology of Kazakhstan". - 2025 - №2 - Р. 202 –217. https://doi.org/10.48081/CSXI4465
Copied!
ANALYSYS OF THE STRUCTURAL STRENGHT OF A TWO SECTION HOPPER CAR UNDER OPERATING CONDITIONS
Annotation
A design improvement for the hopper car has been proposed to allow for the simultaneous transportation of different types of cargo. The enhancement involves dividing the body into two compartments using separate sections that are connected through a vertical partition and horizontal connecting belts. The structural strength of the two-section hopper car was analyzed using the finite element method in SolidWorks Simulation. The results of the study showed that the maximum load of the hopper car occurs in the first constructi e mode (shock). However, the resulting voltages were below the permissible 30%. Modeling was carried out to calculate the indicators of the dynamics of the car. All obtained dynamic indicators were in the maximum permissible results. When transporting a hopper car on railway ferries in international relations, it is recommended to use aggregates for fixing the chain. The study of the dynamic load of the supporting structure of the hopper car was carried out using mathematical modeling. The strength analysis of the supporting structure of the hopper car was carried out. It was found that the stresses in the design of the hopper car do not exceed the regulatory values. The results of the study contribute to increasing the profitability of railway transport. In addition, the results of the work can be useful in the creation of modern carriage structures, including in international communication
Author
А.B.Zabiyeva
Zh. R. Alipbayev
G.N.Baiguzhina
А.B.Sagatbekova
A.E.Toilybayev
DOI
https://doi.org/10.48081/VTWS5358
Keywords
Transport mechanics
hopper car
two-section car
modern car design
wagon loading
profitability of railway transport
Year
2025
Номер
Issue 2
For citation:
А.B.Zabiyeva, Zh. R. Alipbayev, G.N.Baiguzhina, А.B.Sagatbekova, A.E.Toilybayev ANALYSYS OF THE STRUCTURAL STRENGHT OF A TWO SECTION HOPPER CAR UNDER OPERATING CONDITIONS // Scientific journal "Science and Technology of Kazakhstan". - 2025 - №2 - 411 – 422 Б. https://doi.org/10.48081/VTWS5358
Copied!